902 viewsTyler weed eating on my section of the Appalachian Trail. Jun 13, 2026 at 09:31 PM
|
|
861 viewsTrimmed the back edge as well just like the other side. Jun 13, 2026 at 09:29 PM
|
|
866 viewsAFTER trimming the fender (I will trim that top part later after I see if I go with a bushwhacker flare OR if I do something custom) For now I have all the clearance i need and it doesnt look that bad but that will get trimmed eventually !!! Jun 13, 2026 at 09:26 PM
|
|
873 viewsFront bumper lower part trimmed Jun 13, 2026 at 09:24 PM
|
|
893 viewsYep looks good, Jun 13, 2026 at 09:02 PM
|
|
903 viewsHad to drill the slot out so the plastic mounting tab on the trim would fit back in Jun 13, 2026 at 09:02 PM
|
|
846 viewsCoil spring retainer installed on driver side (remember that tower was rusted nearly gone ??) Just one less thing to worry about when going down the trail !! Jun 13, 2026 at 08:56 PM
|
|
827 viewsAFTER !! Jun 13, 2026 at 08:46 PM
|
|
888 viewsThe amount of tools needed for this job. Jun 13, 2026 at 07:22 PM
|
|
694 viewsTyler and I at a remote waterfall. Jun 13, 2026 at 07:01 PM
|
|
892 viewsNew front driveshaft done Jun 13, 2026 at 06:52 PM
|
|
913 viewsFactory setup Jun 13, 2026 at 06:39 PM
|
|
778 viewsPass side. That piece of metal is usually completely removed on these type of jobs but, I decided not to. I cut it and bent it over where the two horns are. I had to modify the horns position so that the wires came down from top instead of sticking out the back which worked well. Jun 13, 2026 at 06:17 PM
|
|
791 viewsMarked the trim for cutting (always go big and then sand it down gradually to get the perfect fit, once its too small you`re screwed !! ) Jun 13, 2026 at 05:59 PM
|
|
849 viewsTyler on the rope taking down trees. Jun 13, 2026 at 05:46 PM
|
|
912 viewstop isolator on rear coil ,, badly squished and worn Jun 13, 2026 at 05:17 PM
|
|
795 viewscleaned the panel Jun 13, 2026 at 05:00 PM
|
|
899 viewsPrimed it well. Jun 13, 2026 at 04:50 PM
|
|
901 viewsRear differential drain plug (if you can call that rubber pos that) leaking so I replaced it with new one and topped off rear end grease as axle grease seals were leaking into the breaks. I will be rebuilding the rear end soon as it has been roaring since I bought it. Jun 13, 2026 at 04:46 PM
|
|
865 viewsTyler helping to bust through the sidewalk so we can remove the old clay gutter drain pipe. Jun 13, 2026 at 04:35 PM
|
|
825 viewsNew gutter drain after removing the old clay pipes. Jun 13, 2026 at 04:31 PM
|
|
859 viewssanded and ready for priming Jun 13, 2026 at 04:16 PM
|
|
820 viewshere is height AFTER the lift and rims/tires. Between the 2.5 lift, new isolators and shocks, I managed to get a total of 6 inches of lift. (was 31 inches) Jun 13, 2026 at 04:16 PM
|
|
836 viewsFront after trimming Jun 13, 2026 at 03:43 PM
|
|
| 268 files on 12 page(s) |
 |
|
|
|
|
|
8 | |
|
|
|
