854 viewsBadly rusted front towerJun 14, 2026 at 12:27 AM
|
|
853 viewssecondly I trimmed a bit off the back edge of the side of it. I did end up taking a wee bit more than pictured here. Jun 14, 2026 at 12:21 AM
|
|
846 viewsTo prevent death wobble I installed a new high perf offroad steering damper shock, out with old and in with new. Jun 14, 2026 at 12:13 AM
|
|
933 viewspassenger side corner piece I made and riveted on, sanded and ready for epoxy Jun 14, 2026 at 12:11 AM
|
|
869 viewsAnother view of the slits I cut in it. Jun 14, 2026 at 12:06 AM
|
|
900 viewsnew rims /tires mounted Jun 14, 2026 at 12:02 AM
|
|
858 viewsinner fender working out well on pass side Jun 14, 2026 at 12:01 AM
|
|
856 viewsNow I replaced the plastic bumper cover so I cut start cutting it. Jun 13, 2026 at 11:44 PM
|
|
864 viewsYou can see how well the inner fender worked out in the front and that shiny bolt is where I had to move it forward 2 inches from the black plastic clip you also see in there Jun 13, 2026 at 11:35 PM
|
|
1248 viewsWhile pass side primer was drying I moved to the driver side. This one went much quicker like under an hour now that I had the process down pat. Jun 13, 2026 at 11:28 PM
|
|
859 viewsTyler working his way down the tree. Jun 13, 2026 at 11:27 PM
|
|
798 viewsNow moving to the rear Jun 13, 2026 at 11:03 PM
|
|
781 viewsAlso new brake rotors and pads on backJun 13, 2026 at 10:51 PM
|
|
871 viewsTyler doing some extreme climbing at a waterfall deep in the Sampson Mtn Wilderness area. Jun 13, 2026 at 10:46 PM
|
|
822 viewsAgain, saving the plastic inner fender I wrapped it around the reservoir and screwed it to the metal bumperJun 13, 2026 at 10:39 PM
|
|
733 viewshere you can see just how high I jacked it up to eliminate so much prying and straining ! Jun 13, 2026 at 10:21 PM
|
|
909 viewsEnd cap fitting nicely ! Jun 13, 2026 at 10:17 PM
|
|
824 viewsNew Bilstein shock installed Jun 13, 2026 at 10:15 PM
|
|
876 viewsTyler taking down more of the big Maple in our yard. Jun 13, 2026 at 10:02 PM
|
|
921 viewsDriver side trimmed Jun 13, 2026 at 09:58 PM
|
|
835 viewsAdded some new fluid to the transfer case as well since you lose some when removing the yoke. Jun 13, 2026 at 09:46 PM
|
|
848 viewsnew blots to mount the bottom of the bumper cover. There are 4 down there and this one was missing almost all. Jun 13, 2026 at 09:43 PM
|
|
862 viewsPass side trimmed Jun 13, 2026 at 09:36 PM
|
|
882 viewsFirst I cut out a large slot in the lower end of the bumper cover Jun 13, 2026 at 09:33 PM
|
|
| 268 files on 12 page(s) |
 |
|
|
|
|
7 | |
|
|
|
|
